How to install Adro's Body Kit on 2017-2022 Tesla Model 3?

How to install Adro's Body Kit on 2017-2022 Tesla Model 3?

Introduction:
Upgrading your Tesla Model 3 with a body kit is an excellent way to enhance its aesthetics and performance. If you are considering acquiring a Tesla Model 3 body kit, please visit this link for purchase options. In this comprehensive guide, we will walk you through the process of installing a body kit on a 2017-2022 Tesla Model 3. Before you begin, ensure that your vehicle is compatible with the installation process by checking the Installation Guide page. Be sure to read this entire article to avoid any mishandling that could result in injury or damage to your Tesla.

Note: The manufacturer is not responsible for any damage caused by the user's mishandling.

Compatibility: This installation guide is compatible with the following Tesla Model 3 variants:

  • 2017-2022 Tesla Model 3 (All trims)

Installation Steps:
This guide covers the installation process for the Carbon Fiber Front Lip V2, Carbon Fiber Side Skirts V2, Carbon Fiber Rear Diffuser V2, and Carbon Fiber Rear Spoiler V2. Follow the step-by-step instructions below to ensure proper installation.

  1. Carbon Fiber Front Lip V2 Installation:
    A. Prep Phase:
    A1. Clean your Model 3's front bumper thoroughly.
    A2. Prep the front bumper with the provided surface primer.
    A3. Fold a small tail of the backing material from the 3M Double-Sided Tape on the underside of the carbon fiber front lip and secure it with masking tape for easy access.

    B. Fit Phase:
    B1. Position the carbon fiber front lip symmetrically.
    B2. Pull the tails on the double-sided tape and press along the taped areas for proper adhesion.

    C. Installation Phase:
    C1. Secure the carbon fiber front lip to the bumper using a power tool and provided components.
  1. Carbon Fiber Side Skirts V2 Installation:
    A. Prep Phase:
    A1. Clean your Model 3's side surfaces thoroughly.
    A2. Prep the carbon fiber side skirts with the provided surface primer and apply double-sided tape.
    A3. Fold a small tail of the red backing material from the 3M Double-Sided Tape and secure it with masking tape for easy access.
    A4. Prep the side surfaces with the provided surface primer.

    B. Fit Phase:
    B1. Position the carbon fiber side skirts symmetrically.
    B2. Pull the tails on the double-sided tape and press along the taped areas for proper adhesion.

    C. Installation Phase:
    C1. Secure the carbon fiber side skirts using a power tool and screws.
  1. Carbon Fiber Rear Diffuser V2 Installation:
    A. Prep Phase:
    A1. Remove factory bolts and save them for later use.
    A2. Clean your Model 3's rear bumper thoroughly.
    A3. Prep the carbon fiber rear diffuser with the provided surface primer and apply double-sided tape.
    A4. Fold a small tail of the red backing material from the 3M Double-Sided Tape and secure it with masking tape for easy access.
    A5. Prep the rear bumper with the provided surface primer.

    B. Fit Phase:
    B1. Position the carbon fiber rear diffuser symmetrically.
    B2. Pull the tails on the double-sided tape and press along the taped areas for proper adhesion.

    C. Install Phase:
    C1. Secure the carbon fiber rear diffuser to the bumper with factory bolts. C2. Secure the carbon fiber rear diffuser to the underbody cover using provided components.
  1. Carbon Fiber Rear Spoiler V2 Installation:
    A. Prep Phase:
    A1. Clean your Model 3's rear trunk thoroughly.
    A2. Prepare the carbon fiber rear spoiler using the provided surface primer and apply the double-sided tape as shown in the accompanying figure.
    A3. Create a small tab from the red backing material of the 3M Double-Sided Tape and secure it with masking tape to ensure easy accessibility.
    A4. Prime the rear trunk surface with the provided surface primer. Exercise caution to avoid overusing the primer, as it may damage the paint job.

    B. Fitting and Installation Phase:
    B1. Carefully align the carbon fiber rear spoiler, ensuring it is perfectly symmetrical to avoid damaging the vehicle
    B2. Once properly aligned, pull the tabs on the double-sided tape and firmly press along the taped areas for secure adhesion.
Back to blog